Burder Ag Attachments is the exclusive distributor for Stoll in Australia. Stoll products are available through Burder’s dealership network.
Stoll manufactures a wide range of agriculture implements and front end loaders that are perfect for a wide range of tractors. The front end loaders are built with a combination of attributes such as power, rigidity, loading performance and modern design and users can be assured of its quality. Stoll produces a wide range of implements such as buckets, pallet forks, bale forks and grabs that are widely used in farming, earth moving, construction and forestry.
|Parking support ensures loader is stable when not in use. Pins on the implement quick-release frame are locked and released externally to ensure safe handling.
|No tools required to disconnect loader thus increasing efficiency. Loader can be disconnected under 1:30 mins.
Reduced Fuel Usage
|Manufactured with best quality high grain steel reduces weight and thus savings on fuel.
|Made in Germany and known for its quality. Withstand all loads even after many years of usage. High quality fine grain steel resulting in increased strength.
Stoll Front End Loaders
STOLL front loaders focus on quality in every detail.
ROBUST AND INNOVATIVE
STOLL constructing engineers succeeded again to combine approved techniques with completely new technical solutions to a modern and impressive loader. You will fast appreciate the benefits of mechanical self levelling by a Z-Kinematik, additional scooping function and rapid dump for many jobs with your tractor. For the laying of hydraulic pipes STOLL gains best notes. Every centimetre of this loader provides confidence. Enter your tractor and look forward to your new FZ / FS front loader.
The new STOLL front loaders FZ / FS combine all attributes like power, rigidity, loading performance and modern design to a new innovative loader concept. These loaders excel in functionality and technical intelligent solutions and will give you pleasure at your daily job by high performance and comfortable handling.
The innovation, which you can expect from a new STOLL front loader. Mechanical self levelling in addition with Z-Kinematik was available before, but the positioning of the control rod inside the rear lift-arm pillar is a skilfully, creative solution, and develops until now not known comfort concerning better view during loader-work and also regarding the construction of the loader. This new concept now acquires the operation-job, which could be realized only with hydraulic guided self levelling loaders.
Caused by this distinctive construction – none upper-located control rods – you will get benefit by better visibility to the loading-material and the driveway, to the front and to the side – this ensures a secured and fast loading-job. Furthermore the Z-Kinematik provides a high performance regarding lifting capacity. The achieved results you can rely on. You will be most excited from this enormously powerful front loader.
Outstanding loading performance by optimum alignment to the tractor
The design of the Z-Kinematik with the control rods inside the rear liftarms works positive for the ideal positioning of loader to tractor – especially by keeping the windscreen openable. By the absence of an overhead control rod the loader is placeable closer to cabin – thus closer to the centre of mass of the tractor. The windscreen stays openable in most cases and the front axle load is reduced. Your tractor will award this with lower wear and higher durability.
Safe standard technology in top STOLL quality.
Sturdy quick-release frame (either Euro or Skid Steer) for implements with safe external controls
The pins on the implement quick-release frame are locked and released externally to ensure safe handling. This means that there is no need to reach into the danger zone between the struts. The process is simple and safe.
Parking supports provide a stable base
The parking supports have been taken straight from the F loaders without any modifications. No tools are required for adjusting them and there are no loose parts involved which can be lost. There is one handle to release the parking supports so that they can fall automatically into the correct parking position. A latched interlock holds the parking supports securely when they have been folded up for loader use.
All bearings with bushes
This is absolutely standard on all STOLL equipment. To ensure that everything runs like clockwork, all the bearings have composite bushes and can be greased from the outside – providing a high level of every day safety for many hours of hard work for the loader.
Good tipping angles
This has always been a strength of all STOLL designs. To ensure that the buckets can be filled properly, they need a good crowd angle on the ground. And to empty them at their topmost position, the buckets must be able to tip as far as possible so that even sticky material can be removed in full from the bucket.
Implements – Buckets
Bucket ROBUST S – Heavy duty design:
ROBUST S heavy duty range for all routine operations with heavy and sticky goods like wet earth or snow.
With tapered shaping of sidewalls – opening to the front – this bucket allows easy discharging of material.
Bucket ROBUST T – Heavy duty design with tines:
ROBUST T heavy duty range like ROBUST S, but with extra welded tines.
This bucket with tear-off tines at wear-resistant cutting edge is best not only for earth moving work, but also heavy tear-off, digging and levelling applications.
Bucket ROBUST U – Universal bucket:
ROBUST U is a bucket for all kind of agricultural routine loader operations.
Buckets of new ROBUST U range are designed for all light and average duty applications. Outer tapered dimensions of sidewalls, depth of bucket table, volume, etc. are the same as ROBUST S range.
Bucket ROBUST M – MAXI-bulk material bucket:
ROBUST M is a high volume heavy duty bucket especially for loader operations with loose light weighted materials.
Buckets of new ROBUST M range are optimized for loading of fertilizer, other granulate materials, grain, bark mulch and wood chips or loosely snow. For applications with high volume and performance per load cycle ROBUST M bucket is first choice.
Implements – Combined Levelling and Grabbing Bucket:
Four functions in one tool:
- Grabbing using the bucket bottom
- Levelling using the bucket back
- Unloading by opening the bucket bottom
- Levelling + grabbing bucket 1.70 m H (0,60 m³)
- Levelling + grabbing bucket 1.90 m H (0,79 m³)
- Levelling + grabbing bucket 2.10 m H (0,91 m³)
Implements – Silage Handling:
To cut silage bales without the driver getting off and without additional implements.
|Height (Closed) in m
|Height (Open) in m
|Width / Length in m
|Maximum Bale Width in m
|Maximum Bale ø in m
|Maximum Bale Weight in kg
|1.82 / 1.10 m
|3rd control circuit required